View HRPG-300-33_4514959.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

300W Single Output with PFC Function
Features :
HRPG-300
series
Universal AC input / Full range Built-in active PFC function, PF>0.95 High efficiency up to 89% (typ.) Withstand 300VAC surge input for 5 seconds Protections: Short circuit / Overload / Over voltage / Over temperature Built-in constant current limiting circuit 1U low profile 41mm Built-in cooling fan ON-OFF control With DC OK signal output Built-in remote ON-OFF control Standby 5V@0.3A Built-in remote sense function No load power consumption<0.5W 5 years warranty
SPECIFICATION
MODEL DC VOLTAGE RATED CURRENT CURRENT RANGE RATED POWER OUTPUT VOLTAGE ADJ. RANGE LINE REGULATION LOAD REGULATION SETUP, RISE TIME HOLD UP TIME (Typ.) HRPG-300-3.3 HRPG-300-5 3.3V 60A 0 ~ 60A 198W 5V 60A 0 ~ 60A 300W 90mVp-p 4.3 ~ 5.8V 2.0% 0.5% 1.0% HRPG-300-7.5 HRPG-300-12 HRPG-300-15 HRPG-300-24 HRPG-300-36 HRPG-300-48 7.5V 40A 0 ~ 40A 300W 100mVp-p 6.8 ~ 9V 2.0% 0.5% 1.0% 12V 27A 0 ~ 27A 324W 120mVp-p 10.2 ~ 13.8V 1.0% 0.3% 0.5% 15V 22A 0 ~ 22A 330W 150mVp-p 13.5 ~ 18V 1.0% 0.3% 0.5% 24V 14A 0 ~ 14A 336W 150mVp-p 21.6 ~ 28.8V 1.0% 0.2% 0.5% 36V 9A 0 ~ 9A 324W 250mVp-p 28.8 ~ 39.6V 1.0% 0.2% 0.5% 48V 7A 0 ~ 7A 336W 250mVp-p 40.8 ~ 55.2V 1.0% 0.2% 0.5%
RIPPLE & NOISE (max.) Note.2 80mVp-p 2.8 ~ 3.8V VOLTAGE TOLERANCE Note.3 2.5% 0.5% 1.0% 16ms/230VAC
1000ms, 50ms/230VAC
2500ms, 50ms/115VAC at full load
16ms/115VAC at full load 120 ~ 370VDC PF>0.99/115VAC at full load 86% 88% 88% 87% 88% 89%
VOLTAGE RANGE Note.5 85 ~ 264VAC FREQUENCY RANGE 47 ~ 63Hz POWER FACTOR (Typ.) INPUT EFFICIENCY (Typ.) AC CURRENT (Typ.) INRUSH CURRENT (Typ.) LEAKAGE CURRENT OVERLOAD OVER VOLTAGE PF>0.95/230VAC 80% 5A/115VAC 35A/115VAC
82% 2.5A/230VAC 70A/230VAC
<1.2mA / 240VAC 105 ~ 135% rated output power Protection type : Constant current limiting, recovers automatically after fault condition is removed 6 ~ 7V 9.4 ~ 10.9V 14.4 ~ 16.8V 18.8 ~ 21.8V 30 ~ 34.8V 3.96 ~ 4.62V Protection type : Shut down o/p voltage, re-power on to recover 90 5 5 (TSW1: detect on heatsink of power transistor) for 3.3V,5V,7.5V ; 95 5 for others (TSW2: detect on heatsink of power diod e) 100
41.4 ~ 48.6V
57.6 ~ 67.2V
PROTECTION
OVER TEMPERATURE 5V STANDBY FUNCTION DC OK SIGNAL REMOTE CONTROL FAN CONTROL (Typ.) WORKING TEMP.
Protection type : Shut down o/p voltage, recovers automatically after temperature goes down 5VSB : 5V@0.3A ; tolerance 5%, ripple : 50mVp-p(max.) PSU turns on : 3.3 ~ 5.6V ; PSU turns off : 0 ~ 1V RC+ / RC-: 4 ~ 10V or open = power on ; 0 ~ 0.8V or short = power off Load 35 15% or RTH2 -30 ~ +70 50 Fan on (Refer to output load derating curve)
20 ~ 90% RH non-condensing WORKING HUMIDITY ENVIRONMENT STORAGE TEMP., HUMIDITY -40 ~ +85 , 10 ~ 95% RH TEMP. COEFFICIENT 0.03%/ (0 ~ 50 ) VIBRATION 10 ~ 500Hz, 5G 10min./1cycle, 60min. each along X, Y, Z axes SAFETY STANDARDS WITHSTAND VOLTAGE SAFETY & EMC
(Note 4)
UL60950-1, TUV EN60950-1 approved I/P-O/P:3KVAC I/P-FG:1.5KVAC O/P-FG:0.5KVAC / 70% RH
ISOLATION RESISTANCE HARMONIC CURRENT EMS IMMUNITY MTBF
I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25 EMI CONDUCTION & RADIATION Compliance to EN55022 (CISPR22) Class B
Compliance to EN61000-3-2,-3 Compliance to EN61000-4-2,3,4,5,6,8,11, ENV50204, EN55024, EN61000-6-2, heavy industry level, criteria A 176K hrs min. MIL-HDBK-217F (25 ) 199*105*41mm (L*W*H) 0.95Kg;15pcs/15.3Kg/0.69CUFT
OTHERS
DIMENSION PACKING
NOTE
1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature. 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Tolerance : includes set up tolerance, line regulation and load regulation. 4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives. 5. Derating may be needed under low input voltages. Please check the derating curve for more details.
File Name:HRPG-300-SPEC 2009-11-09
300W Single Output with PFC Function
Mechanical Specification
HRPG-300
Case No.980A
18 12.5
series
Unit:mm
4-M4 L=6 168.5
R2 .25
168.5 199
12.25
1.5 HOLE IN CHASSIS
4.5
18
168.5 120
12.25 42.5
1
11
Terminal Pin No. Assignment
Pin No. 1 2 3 Assignment AC/L AC/N FG Assignment Pin No. DC OUTPUT -V 4,5 6,7 DC OUTPUT +V
2 3 4 5 6 7 LED CN100 SVR
4-M4 L=5
4-M4 L=6
Block Diagram
AUX POWER EMI FILTER ACTIVE INRUSH CURRENT LIMITING RECTIFIERS & PFC O.T.P. FG PFC CONTROL PWM CONTROL POWER SWITCHING O.L.P.
RECTIFIERS & FILTER RECTIFIERS & FILTER DETECTION CIRCUIT O.V.P. REMOTE CONTROL
I/P
Derating Curve
Output Derating VS Input Voltage
Ta = 25
100
100 90
80
80 70
60
LOAD (%)
50 40
LOAD(%)
60 50 40
20
-30
0
10
20
30
40
50
60
70
(HORIZONTAL)
85
100
125
135
155
AMBIENT TEMPERATURE ( )
INPUT VOLTAGE (V) 60Hz
File Name:HRPG-300-SPEC 2009-11-09
12.5 18 41
Pin No. Assignment AUX 1 AUXG 2 DC-OK 3 RC4 GND 5 RC+ 6 +S 7 -S 8
Mating Housing
Terminal
167.5 167.5 12.25 12.25
HRS DF11-8DS or equivalent
HRS DF11-**SC or equivalent
17max.
15
Connector Pin No. Assignment (CN100) : HRS DF11-8DP-2DS or equivalent
75 105 125
9.2
FAN
Air flow direction
17
28
fosc : 70KHz
AUX AUXG +S +V -V -S DC-OK
RC+ RC-
264
300W Single Output with PFC Function
Function Description of CN100
HRPG-300
series
Pin No. Function Description Auxiliary voltage output, 4.6~5.25V, reference to pin 2(AUXG). The maximum load current is 0.3A. This output has the built-in oring 1 AUX diodes and is not controlled by the "remote ON/OFF control". 2 3 4 5 6 7 8 AUXG DC-OK RCGND RC+ +S -S Auxiliary voltage output ground. The signal return is isolated from the output terminals (+V & -V). DC-OK signal is a TTL level signal, referenced to pin5(DC-OK GND). High when PSU turns on. Remote control ground. This pin connects to the negative terminal(-V). Return for DC-OK signal output. Turns the output on and off by electrical or dry contact between pin 4 (RC-), Short: Power OFF, Open: Power ON. Positive sensing. The +S signal should be connected to the positive terminal of the load. The +S and -S leads should be twisted in pair to minimize noise pick-up effect. The maximum line drop compensation is 0.5V. Negative sensing. The -S signal should be connected to the negative terminal of the load. The -S and +S leads should be twisted in pair to minimize noise pick-up effect. The maximum line drop compensation is 0.5V.
Function Manual
1.Remote Sense The remote sensing compensates voltage drop on the load wiring up to 0.5V.
CN100 1 AUX DC-OK GND RC+ +S -S 7 8
1
2
3
4
5
6
7 CN100
2 AUXG RC-
17 28
-S (Pin8)
LOAD +
+S (Pin7)
Sense lines should be twisted in pairs
Fig 1.1
2.DC-OK Signal DC-OK signal is a TTL level signal. High when PSU turns on.
Between DC-OK(pin6) and GND(pin4) 3.3 ~ 5.6V 0 ~ 1V Output Status ON OFF
CN100
1 2 3 4 5 6 7 CN100
1
AUX DC-OK GND RC+
+S -S
7 8
2 AUXG RC-
17 28
Fig 2.1
File Name:HRPG-300-SPEC 2009-11-09
300W Single Output with PFC Function
HRPG-300
series
3.Remote Control The PSU can be turned ON/OFF by using the "Remote ON/OFF" function
Between RC+(pin3) and RC-(pin5) SW ON (Short) SW OFF (Open) Output Status OFF ON
CN100 1 AUX DC-OK GND RC+ +S -S 7 8
1
2
3
4
5
6
7 CN100
2 AUXG RC-
17 28
SW Fig 3.1
File Name:HRPG-300-SPEC 2009-11-09

▲Up To Search▲

Price & Availability of HRPG-300-33

	To Download HRPG-300-33 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .